POWERCLEAN SPECIAL PAINT REMOVER

 

 Product features

• Based on slowly evaporating alcohols and special solvents

• Mild odour

• Long-lasting and intensive dissolving power

• Removal of several layers of paint in one step

• Causes no alteration of the stripped building substance

• Restores mineral substrates pore-deeply

• Wood does not fray or discolour

• High flash point

 

Scope of application

• Wood, metal, stucco, mineral and solvent-free substrates

• Concrete, pure mineral plasters, all types of natural stone

• Masonry such as clinker, brick, etc.

• Indoor and outdoor application

 

Technical limits

Not suitable for on plastic surfaces. Paint removal is not possible on plastics that contain plasticisers. If in doubt, test substrate compatibility for resistance before application. Thoroughly cover surfaces that are not to be stripped.

 

Technical information

Density at 20°C: 1,09 g/cm³

Colour: white-opaque

Odour: mild-aromatic

Viscosity: 3000 - 6000 mPas

pH-value at 20°C: 6,0

Flash point:82°C

Minimum processing temperature:10°C

Storage/shelf life: cool and dry in the closed original container for at least 24 months

Water hazard: WGK 1 (water hazard class)

Consumption: 250 ml/m² – 2 l/m2 (ca. 100 ml per paint/lacquer layer to be removed)

 

Application

Powerclean Special Paint Remover dissolves and removes aqueous lacquers (acrylic based), 2-component paints, adhesives, epoxy, synthetic resin paints, oil paints (conditional) and elastic coating systems.

 

Development of characteristics:

Powerclean Special Paint Remover is a paint stripper based on slowly evaporating solvents that dissolve the binder system of the paints to be removed so that they can be easily stripped or washed off. In order to enable the full development of the dissolving characteristics, make sure that enough material has been applied. If too less Powerclean has been applied, the surface will become dry and whitish-yellowish. In this case, do not remove with water, but apply Powerclean again; the dissolving process will be reactivated. The dissolved coatings should always be removed at the optimum dissolving point (saving cleaning time, minimises costs).

 

Disturbing influences:

Damp substrates, rain, draughts, low temperatures (cold), very highly absorbent substrates, insufficient ventilation during application, insufficient application of material.

Supportive influences:

Warm temperatures, covering the stained surfaces with thin PE film (not a must!); indoors, this significantly minimises the development of odours. Sufficiently long exposure time (test areas).

 

Exposure Time:

At least 30 minutes up to 1 hour, days (under foil). Determine the optimal exposure time by creating a test area.

 

Processing

 

Preparatory measures:

The object conditions or ambient conditions must be checked (see property development). If the dissolved coatings are removed with a hot water high-pressure cleaner, collection devices must be planned as part of the scaffolding installation (see removal procedure). The object must be registered due to the responsible authorities. When Powerclean Special Paint Remover is applied using the airless method, it is recommended to suspend the scaffold with tarpaulins and to pay special attention to the safety instructions.

Powerclean Paint Remover is ready for use and is not allowed to be modified. Open the container. If liquid has settled (this is not a defect), stir the product well.

Apply Powerclean Special Paint Remover evenly with an airless applicator, brush, trowel, roller, spatula, trowel or smoothing trowel (no plastic bristles).

Application by airless method: completely remove filters and sieves in the unit

Standard nozzles: mm/inch 0,530/0,021 bis 1,070/0,043

Working pressure: 40 - 80 bar depending on the nozzle used

Air-pressure operated airless device: working pressure approx. 2 bar

 

Removal of dissolved coatings:

General:

The removal of dissolved coatings should always be carried out directly at the optimum time for dissolution. The longer the already dissolved coating remains on the mineral substrate, the more the wash-off behaviour deteriorates, which may lead to longer cleaning times or longer times for removal. The solvents penetrate deeper into the substrate on soft and open-pored substrates. The evaporation of the solvents from the substrate can therefore take several days.

 

 

 

Specifications

 

Appearance:

Viscous opaque gel

 

 

Composition:

Benzyl alcohol (>90%)

 

Viscosity:

3000 - 6000 mPas

 

 

Minimum processing temperature:

10 oC

 

 

Solubility:

Partially soluble in water

Photo Code Title Quantity
POWERCLEAN SPECIAL PAINT REMOVER 1lt 05.01.00.033 POWERCLEAN SPECIAL PAINT REMOVER 1lt Add this item to the basket